Your search for binders resulted in 24 matches...
The article presents the results of laboratory tests on the binding characteristics of moulding sands with inorganic geopolymer binders and for comparison with furan resin and alkaline resin, designed for casting o...
more >>
The article presents the results of laboratory and industrial tests on the application of a new geopolymer Rudal A binder used in production of moulding and core sands for castings from carbon and alloyed cast stee...
more >>
The article gives the results obtained in a fragment of the studies, carried out under a statutory activity, on optimising of the foundry sand technology with new modified inorganic binders, chemically bonded and C...
more >>
The paper presents the results of laboratory and industrial tests undertaken in order to develop and implement in foundry production the high-quality bentonite made from the raw dried material and selected fractions formed in the production of hyg...
more >>
The article presents results of an investigation which constitutes a section of research under the project POIG.01.01.02-00-015/09 "Advanced materials and technologies", one of the aims which is the introduction of new ecological inorganic binders...
more >>
The article presents results of laboratory tests to develop a new generation of foundry hybrid bentonite. Hybrid bentonite is intended for use as binder for synthetic moulding sands and sandmixes. In the previous practice foundry bentonite was a p...
more >>
One of the factors which influence development tendencies within the scope of moulding sands used in foundry practice is environmental protection. Hence, while assessing technologies, the composition of utilised materials and emissions of harmful ...
more >>
Tests were conducted to develop a new generation of functional nano-coatings used in the foundry industry. The research focused on the introduction of modern and innovative coatings based on nanoparticles of cast elements and active chemical compo...
more >>
This paper presents the method of investigating the sol-gel transition by constant speed removal of plates, made of suitable substrate, from an aqueous colloidal binder. The thickness of the deposited colloidal binder layer depends on the particle...
more >>
Among various sands with organic binders, moulding sands with furan resins belong to the group most widely applied in the manufacture of castings from ferrous alloys. This is due to a number of undisputable advantages offered by these sands, altho...
more >>
The article presents the results of preliminary studies on the possible application of innovative activation treatments of inorganic binders during the reclamation of waste water glass moulding sands hardened by conventional drying. The test mould...
more >>
The article presents the results of tests and studies carried out within the framework of statutory activities on various additives to moulding sands based on water-soluble inorganic binders for ablative knocking out of castings. As a result of te...
more >>
The article presents the results of research on the possibilities of utilizing waste moulding sands with silicate and geopolymer binders in the production of autoclaved cellular concrete. The high content of silica in the waste moulding and core s...
more >>
The paper presents the results of analysis of gases formed under the impact of high temperature acting on moulding sands with the addition of selected organic resins and hardeners, commonly used in foundries as binders for these sands. As a resear...
more >>
An attempt has been made to determine the effect of the addition of an agent wetting the surface of silica sand grains, introduced in order to increase the hardening efficiency of selected physical methods applied to the ecological foundry sands b...
more >>
Loose rapid hardening masses with synthetic resins, customarily called cold-box technologies, have dominated the process of casting core production. A distinguishing feature of these technologies is the manner of mass preparation without the use o...
more >>
The article presents an analysis of the kinetics of the hardening process of self-hardening masses. In this study, moulding sand with a quartz sand grain matrix by Sibelco, main fraction Fm 0.40; 0.32; 0.20 mm, was used. Two resins were...
more >>
The increasing requirements concerning the emission of hazardous substances force the casting industry to search for new, more environment-friendly solutions. Such solutions may include technologies of developing moulding and core sands with the u...
more >>
The article presents the results of the pyrolysis of resin, the fast hardener as well as cured resin used in the ALPHASET technology. It is an alkaline phenolic resin of the resol type cured with an ester mixture. The pyrolysis was performed at 90...
more >>
Protective coatings are applied in order to obtain casts with an even surface, without faults. Protective coatings can contain a solvent based on water or alcohol; however, due to their harmfulness, it is recommended to limit the use of alcohol co...
more >>
The study attempts to complement the information on the effect of the density of moulding sands with inorganic binders on basic strength parameters, i.e. the tensile and bending strength of moulding sands with hydrated sodium silicate, after the p...
more >>
The article discusses the ways of modification of hydrated sodium silicate as a silicate binder of moulding sands which were applied in the studies. It determines the change in the residual strength of the moulding sand with used silicate binders ...
more >>
This article presents selected research methods related to protective coatings used for sand moulds and cores in the foundry industry. The research methodology has been divided into studies of the technological properties of sand moulds and cores ...
more >>
Testing the properties of mould and core sands are specified in the norms and standards, which are used to determine the suitability of the sand for specific applications. However, the testing of protective coatings for moulding&nbs...
more >>
| 
